Toggle menu
3018927093
  • DINITROL DIRECT FW Primerless Automotive Urethane / 600ml 2 Foil-Wrap
  • DINITROL DIRECT FW Primerless Automotive Urethane / 600ml 2 Foil-Wrap
  • DINITROL DIRECT FW Primerless Automotive Urethane / 600ml 2 Foil-Wrap
  • DINITROL DIRECT FW Primerless Automotive Urethane / 600ml 2 Foil-Wrap
  • DINITROL DIRECT FW Primerless Automotive Urethane / 600ml 2 Foil-Wrap
  • DINITROL DIRECT FW Primerless Automotive Urethane / 600ml 2 Foil-Wrap

    • DINITROL DIRECT FW Primerless Automotive Urethane / 600ml 2 Foil-Wrap

    Dinitrol

    MSRP: $50.99
    $29.95
    (You save $21.04 )
    (No reviews yet) Write a Review
    SKU:
    DINITROL DIRECT FW 2 Foil
    UPC:
    648609872460
    Condition:
    New
    Width:
    9.00 (in)
    Height:
    4.00 (in)
    Depth:
    12.00 (in)
    Bullet Point 1:
    Benefits: - Primerless to Glass - High Viscosity - Excellent Working Time - Good Decking - Fast Curing - Short cut-off String - High Elasticity - Crash Test Proven to FMVSS
    Bullet Point 4:
    Fast Curing times Safe Drive Away Time - 3hr+ depending on temperature and humidity - check description for exact cure times.
    Bullet Point 5:
    (2) 600ml Foil - equivalent to 4 tubes/cartridges. Require sausage style caulking gun to dispense.
    Package Length:
    12.00
    Package Width:
    9.00
    Package Height:
    4.00
    Warranty:
    2 Years
    Country of Manufacture:
    Switzerland

    Out of stock

    Product Description

    DINTROL Direct FW is a primerless urethane. Manufacture always recommends safe practices to apply a primer or activator prior to installing a windshield. All bonding areas must be clean, dry and free from all contaminates like oil, grease, release agents, etc.
    Important Notes: Glass installation is not recommended at temperatures below 5 C (40 F) unless proper procedures are following as stated in the DINITROL AGR Training Manual under Adverse Weather Conditions Section. Adhesives such as DINITROL 9100 or DINITROL 9000 should be used in these extreme temperatures unless glass is replaced in a heated shop an allowed to remain there until the appropriate Safety Drive Away Time as listed on the product TDS sheets have been met.
    This product requires a 26:1 thrust ratio caulk gun or better to properly dispense.



    *For complete instructions on how to use and apply the DINITROL glass bonding systems, please refer to the DINITROL AGR Training Manual.
    *This product is a professional use product and should only be used by certified technicians. The seller highly recommends the buyer to use a professional auto glass installer for proper knowledge and use of this product. The buyer agrees to hold harmless seller and manufacturer for any liability with regard to the use and handling of this product. The buyer understands that by purchasing this product to use themselves without the use of a professional as recommend by the seller and manufacturer serious injury or death may result.*

    Other Details

    Y

    Product Videos

    Custom Field

    Bullet Point 1 Benefits: - Primerless to Glass - High Viscosity - Excellent Working Time - Good Decking - Fast Curing - Short cut-off String - High Elasticity - Crash Test Proven to FMVSS
    Bullet Point 4 Fast Curing times Safe Drive Away Time - 3hr+ depending on temperature and humidity - check description for exact cure times.
    Bullet Point 5 (2) 600ml Foil - equivalent to 4 tubes/cartridges. Require sausage style caulking gun to dispense.
    Package Length 12.00
    Package Width 9.00
    Package Height 4.00
    Warranty 2 Years
    Country of Manufacture Switzerland

    Product Reviews

    Write a Review