Product Description
PUR-505 can also be used with Dinitrol 538 Plus multi-function black primer for superior adhesion and 100 % UV blocking on all OEM and Aftermarket vehicle glass.PUR-505 is a one component cold applied, non-conductive urethane adhesive system.Important Notes: Glass installation is not recommended at temperatures below 5 C (40 F) unless proper procedures are followed as stated in the DINITROL AGR Training Manual under Adverse Weather Conditions Section. Adhesives such as DINITROL 9100 or DINITROL 9000 should be used in these extreme temperatures unless glass is replaced in a heated shop an allowed to remain there until the appropriate Safety Drive Away Time as listed on the product TDS sheets have been met. *For complete instructions on how to use and apply the DINITROL glass bonding systems, please refer to the DINITROL AGR Training Manual.
2 tubes of urethane required for most windshield or back glass installations. 1 tube for most other glass installations.
This product requires a 26:1 thrust ratio caulk gun or better to properly dispense.
| RH/TEMP | > 70% | > 50% | > 30% | > 10% |
| > 85°F (30°C) | 3 hrs | 3 hrs | 3 hrs | 8 hrs |
| > 73°F (23°C) | 3 hrs | 3 hrs | 4 hrs | 10 hrs |
| > 60°F (15°C) | 3 hrs | 3 hrs | 5 hrs | 16 hrs |
| > 50°F (10°C) | 5 hrs | 5 hrs | 12 hrs | 24 hrs |
| > 40°F (5°C) | 9 hrs | 9 hrs | 18 hrs | 30 hrs |
* Application at or below 40°F is Not Recommended
*This product is a professional use product and should only be used by certified technicians. The seller highly recommends the buyer to use a professional auto glass installer for proper knowledge and use of this product.
The buyer agrees to hold harmless seller and manufacturer for any liability with regard to the use and handling of this product.
The buyer understands that by purchasing this product to use themselves without the use of a professionalas recommend by the seller and manufacturer serious injury or death may result.*
*This product is a professional use product and should only be used by certified technicians. The seller highly recommends the buyer to use a professional auto glass installer for proper knowledge and use of this product.
The buyer agrees to hold harmless seller and manufacturer for any liability with regard to the use and handling of this product.
The buyer understands that by purchasing this product to use themselves without the use of a professionalas recommend by the seller and manufacturer serious injury or death may result.*
DINITROL 538 Plus is a one-step primer for windscreen bonding. DINITROL 538 Plus is a solvent containing, physically and chemically drying black primer which promotes the adhesion between the glass/paint surface and the direct glazing adhesive and acts as a UV protection.
- One-step glass primer for the ceramic coating
- Pretreatment of RIM and paints
- Long life primer (no reaction within 3 months)
- Inhibits rust in small nicks and scratches
- Compatible with all DINITROL adhesive systems
Application temperature 5 C - 40 C - Application method felt / brush
Drying time > 5 min *
Adhesion with direct glazing Polyurethanes on glass-frit:
- with activator - good
- without activator - good
Shelf life 12 months
Important Note:
Due to its reactivity with moisture, the primer has to be used within 1 week after bottle has been opened (if properly sealed). DINITROL 538 Plus should not be used if the product has remained opened for an extended amount of time. Replace inner seal and cap tightly and immediately after each use to ensure maximum shelf life. This product is suitable for experienced professional users only.
Product Videos
Custom Field
Number of Items 1
OEM Number 1263277
Bullet Point 5 (1) 310ml tube/cartridges and (1) 538 Plus (10ml) Primer Stick. Require cartridge style caulking gun to dispense.
Bullet Point 4 Fast Curing times Safe Drive Away Time - 3hr+ depending on temperature and humidity - check description for exact cure times.
Bullet Point 3 Method of use: The application of the DINITROL PUR-505 requires a power caulking gun or 26:1 thrust ratio to properly dispense. The use of this product is suitable only for experienced users. Pre-tests are recommended for special applications.
Bullet Point 2 This urethane doesn't requires the use of primer, this is a primerless to glass urethane. All bonding areas must be clean, dry and free from all contaminates. If there is no existing urethane on the pinchweld, apply 538 plus to the bonding area.
Bullet Point 1 Benefits: - Primerless to Glass - High Viscosity - Excellent Working Time - Good Decking - Fast Curing - Short cut-off String - High Elasticity - Crash Test Proven to FMVSS
